35 Series Features

• Velocity and Reduction Rate measurements are standard on all models
• Wide thickness range from 0.0030" to 25.0" (0.08 mm to 635.0 mm) depending on instrument and material
• Uses contact, delay line, and immersion transducers
• Application Auto-Recall with default and custom setups
• Hand-held; weighs only 8.5 oz. (0.24 kg)
• Min/Max Mode
• Hi-Low alarm
• English and metric display (inches/mm)
• Multi-language user interface
• Long battery life

Models 35 and 35DL

Models 35 and 35DLare used in the majority of applications
The 35 and 35DL can use transducers ranging from 2.25 to 30 MHz, which means that these versatile gages can solve the majority of thickness gaging applications, from very thin to very thick. In general, transducers with higher frequencies and smaller diameters allow measurements of thinner or curved parts and enhance the accuracy of the measurement.

Applications
• most materials, from thin to thick
• plastic bottles, tubes, pipes, sheets as thin as 0.08 mm (or 0.003 inch)
• metal containers, steel coils, machined parts as thin as 0.10 mm (or 0.004 inch)
• cylinder bores, turbine blades
• glass bulbs, bottles
• thin fiberglass, rubber, ceramics, and composite materials
• curved areas or containers with small radii
• resolution up to 0.001 mm or 0.0001"

Models 35HP and 35DL-HP

With a very low ultrasonic frequency bandwidth and a special pulser-receiver, the HP gages are specifically designed to optimize ultrasound penetration when measuring thick, highly sound attenuating or sound scattering materials. Typically these materials cannot be measured with most other ultrasonic thickness gages.

Applications
• most thick or sound-attenuating materials
• thick cast metal parts
• thick rubber tires, belts
• fiberglass boat hulls, storage tanks
• composite panels
• resolution of 0.01 mm or 0.001"
of 0.01 mm or 0.001"

The 35HP gages are excellent tools to measure fiberglass or composite parts, from aerospace structures to boat hulls and storage tanks that require thickness control.

Why HP gages
For more than three decades, Panametrics-NDT thickness gage engineers have developed the HP (High Penetration) series specifically for very sound-attenuating or thick materials. Not only can these gages use transducers as low as 0.5 MHz but their electronics (pulser-receiver) are highly optimized to process signals at these low frequencies. The result is that the Panametrics-NDT gages have earned a reputation for superior performance in measuring thick rubber, fiberglass, composites, and other tough materials.

Other 35 Series Features

With reduction rate you can measure critical thickness metal thinning caused by bending.

Velocity measurement mode with direct Velocity readout.

Material Sound Velocity Measurements
All 35 models have the capability to make material sound velocity measurements. This standard feature is useful in applications where the speed of the sound within the material can be correlated to other properties. Typical applications include cast metals to monitor the degree of nodularity, and composites/fiberglass to monitor variations in density. Olympus NDT offers a digital caliper for automatic transfer of measurement thickness.Application Auto-Recall Simplifies Gaging
Application Auto-Recall simplifies making thickness measurements. Select any of the stored transducers and the 35 gages recall all relevant internal transducer parameters.
Stored Standard Setups
Standard setups include most commonly used transducers.
Stored Custom Setups
Just in case your special application problem cannot be solved with a Standard Setup, these gages can create, store, and recall as many as 20 Custom Setups (10 with the 35 and 35HP).

Micrometers won't work in this classic application. Instead, the Model 35 with a M208 transducer makes a thickness measurement up to a calibrated accuracy of 0.001 mm (or 0.0001 inch) without breaking the glass.

Thickness and waveform of a very thin (0.004 inch or 0.10 mm) sheet of steel.

35PCSCOPE

Optional 35PCSCOPE interface software permits the instant display of live ultrasonic waveforms and thickness readings directly on your computer screen. This is helpful when setup parameters require closer examination.

Now You Can See The Live Waveform And Make Adjustments

Operator can view thickness and waveform with the optional A-scan mode

An optional Live Waveform Mode on all models permits the user to view the ultrasound waveform (or A-scan) directly on the gage's display to make sure the thickness reading is correct. The Adjust Mode feature facilitates transducer setup adjustments to maximize measurement performance for challenging applications.
• High pixel density LCD renders sharp trace of live waveform
• Permits real-time verification of thickness readings
• Helps solve many difficult applications
• A Range, Delay, or Zoom allow enlarging and centering to any section of the waveform
• Permits adjustments of transducer setup parameters
• Stores waveforms in data logger and transfers to PC

Why ultrasonics?
Ultrasonic measurements are accurate, reliable, and repeatable. Instant digital readings can be achieved by transmitting sound into just one side of a material, making it unnecessary to cut or destroy parts where the opposite side is difficult to reach and where micrometers or other inspection tools cannot do the job.

35, 35DL, 35HP and 35DL-HP Specifications*

Differential Mode: Displays thickness difference between actual measurement and reference value.

Reduction Rate Mode: Displays thickness and percent difference between actual measurement and reference value.

Application Auto-Recall: Automatically adjusts internal parameters for various default and custom transducer setups.

	# of Default	# of Custom
35	21	10
35DL	21	20
35HP	17	10
35DL-HP	17	20

Other Standard Features: Calibration Lock Mode, Internal Diagnostic Test Mode, Metric/English Units, On-board Statistics (35DL and 35DL-HP only)

POWER SUPPLY
Battery: 3 AA alkaline or NiMH batteries
Operating Time: 150 hours typical battery life; 30 hours continuous with backlight on
Low Battery Indicator: Continuously indicates battery status.
BatterySaver: Auto Power Off/Continuous On
AC Power Supply: Optional

GENERAL
Environmental IP-65 compliant:
Splash-proof, impact-resistant case. Sealed, color-coded keypad with tactile and audible feedback.
Operating Temperature Range:
-10°C to +50°C (+14°F to 122°F)
Size: 3.31" W x 6.0" L x 1.50" H
(84 x 152 x 84 mm)
Weight: 8.5 oz. (0.24 kg)
Custom Language Utility: Allows translation of display text in many languages.

35DL & 35DL-HP
INTERNAL DATA LOGGER
Data Logger: The 35DL & 35DL-HP identify, store, recall, clear, and transmit thickness readings and transducer setup information via the USB port or optional RS-232.
Max. # of Stored Values: Over 8,000 or 350 waveforms with thickness readings (with Waveform Option)
Stored Data Documentation: Each saved thickness reading is fully documented with measurement status flags and a setup number that identifies parameters such as velocity, transducer, etc.
File Name Length: 8 alphanumeric characters
Identification Codes: 10 character alphanumeric Identification Code system identifies or locates stored data
4 File Templates: Incremental, Sequential and 2D Grid. Manual files from PC.

STANDARD INCLUSIONS
Wrist Strap, 3 AA Batteries, Test Block, Transducer Cable, Couplant, Carrying Case, Instruction Manual, Two-Year Limited Warranty

OPTIONAL ACCESSORIES
35/WF	Live Waveform
Gageview	Interface Program
35DL/RS232	RS-232 output
35DLHP/RS232	RS-232 output
35PCScope	PCScope Program
USB/ADP-115	AC-115 Power Supply
USB/ADP-230	AC-230 Power Supply
MG2/RPC	Protective Rubber Boot
35/DLRETRO	Upgrade 35 to 35DL
35HP/DLRETRO	Upgrade 35HP to 35DL-HP